Simple FM Slope Detector

The circuit diagram of a simple slope detector is as shown in figure 1.

Fig.1 : Simple Slope Detector

The output voltage of the tank circuit is then applied to a simple diode detector of an RC load with proper time constant.

This detector is identical to the AM diode detector. Even though the slope detector circuit is simple it has the following drawbacks.

Drawbacks of Slope Detector

(i) It is inefficient.

(ii) It is linear only over a limited frequency range.

(iii) It is difficult to adjust as the primary and secondary winding of the transformer must be tuned to slightly different frequencies.

Advantages of Slope Detector

The only advantages of the basic slope detector circuit is its simplicity.

To overcome the drawbacks of the simple slope detector, a Balanced slope detector is used.

Balanced FM Slope Detector (Balanced Frequency Discriminator)

The circuit diagram of the balanced slope detector is shown in Figure. 2.

Fig.2 : Balanced Slope Detector

As shown in the circuit diagram, the balanced slope detector consists of two slope detector circuits.

The input transformer has a center tapped secondary. Hence, the input voltages to the two slope detectors are 180° out of phase.

There are three tuned circuits.

Out of them, the primary is tuned to IF i.e., fc .

The upper tuned circuit of the secondary (T1) is tuned above fc  by Δf i.e., its resonant frequency is (fc+ Δf).

The lower tuned circuit of the secondary is tuned below fc by Δf i.e., at (fc – Δf).

R1C1 and R2C2 are the filters used to bypass the RF ripple.

Vo1 and Vo2 are the output voltages of the two slope detectors.

The final output voltage Vo is obtained by taking the subtraction of the individual output voltages, Vo1 and Vo2, i.e.,

Working Operation of the Circuit

The circuit operation can be explained by dividing the input frequency into three ranges as follows:

(i) fin = fc: When the input frequency is instantaneously equal to fc, the induced voltage in the T1 winding of secondary is exactly equal to that induced in the winding T2.

Thus, the input voltages to both the diodes D1 and D2 will be the same.

Therefore, their dc output voltages Vo1 and Vo2 will also be identical but they have opposite polarities. Hence, the net output voltage Vo = 0.

(ii) fc < fin < (fc + Δf): In this range of input frequency, the induced voltage in the winding T1 is higher than that induced in T2.

Therefore, the input to D1 is higher than D2.

Hence, the positive output Vo1 of D1 is higher than the negative output Vo2 of D2.

Therefore, the output voltage Vo is positive.

As the input frequency increases towards (fc + Δf), the positive output voltage increases as shown in 3.

Fig.3: Characteristics of the balanced slope detector

If the output frequency goes outside the range of (fc – Δf) to (fc + Δf), the output voltage will fall due to the reduction in tuned circuit response.

Advantages

(i) This circuit is more efficient than simple slope detector.

(ii) It has better linearity than the simple slope detector.

Drawbacks

(i) Even though linearity is good, it is not good enough.

(ii) This circuit is difficult to tune since the three tuned circuits are to be tuned at different frequencies i.e., fc, (fc+Δf) and (fc – Δf).

(iii) Amplitude limiting is not provided.

Sasmita

Hi! I am Sasmita . At ElectronicsPost.com I pursue my love for teaching. I am an M.Tech in Electronics & Telecommunication Engineering. And, if you really want to know more about me, please visit my "About" Page. Read More

Share
Published by
Sasmita

Recent Posts

A Complete Guide to Advanced PCB

A PCB is the primary building block of any electronic design and over recent years…

6 days ago

The Tombstone Effect in Reflow Soldering

Tombstoning is one of the many issues that Rush PCB and other PCB assemblers face…

2 weeks ago

Transparent PCB with PET Base by PCBWay

To satisfy the increasing needs and requirements of various electronics and electrical devices, the PCB…

2 weeks ago

5th PCB Design Contest by PCBWay

PCBWay is one of the most experienced PCB manufacturing company based in China with an…

3 weeks ago

8051 Microcontroller Architecture and Application

The 8051 Microcontroller is one of the most commonly used microcontrollers, designed by Intel  in…

3 months ago

PCBWay OEM Services – The One Stop Solution

What is OEM ? OEM stands for Original Equipment Manufacturer. Basically it is a company…

3 months ago